Understanding thermochemical storage without equations
Storing heat by separating and recombining compounds (reversible reaction)
Thermochemical storage works like a heat battery. During the charging phase, you supply energy to separate a reactive pair (often through dehydration or decomposition). As long as the two “parts” stay isolated, the energy is retained with very low losses. During discharge, you bring the reactants back into contact. The reverse reaction releases heat.
Thermal sorption: adsorption and absorption, and what changes on site
In adsorption, water vapour binds to the surface of a solid (zeolite, silica gel). In absorption, it penetrates into a liquid or a porous solid. On site, this mainly translates into permeability and heat-transfer requirements. Without good material-to-heat-exchanger contact, the kinetics slow down and useful power collapses.
The system families: hydrates, salts, zeolites and other reactive materials
The best-documented routes are salt hydrates (for example chlorides, sulfates), zeolites and certain metal oxides (for example lime). Each family comes with its own constraints: corrosion, humidity management, cycling. In 2026, the market is still dominated by demonstrators and pilot systems. Not a mainstream retrofit product. For comparison with another storage approach based on phase change materials, useful when you want to smooth gains without a chemical reaction.
Salt-based heat storage: what you need to remember about salt/water pairs
The “salt” in practice: hydrate, dehydrate, and recover the heat
In a salt/water pair, the heat comes from a reversible reaction. During charging, you dehydrate a hydrated salt using a heat source and store the energy as chemical potential. During discharge, you reintroduce water vapour or moist air. The salt rehydrates and releases heat. That is thermochemical storage. In 2026, the field is still mostly at demonstrator and pilot-module level, not at “catalogue product” level.
Charge/discharge cycle: temperature, humidity and air quality conditions
The cycle works if you control three parameters. First, the temperature levels available for desorption; otherwise charging remains incomplete. Second, humidity on the discharge side. A poorly controlled dew point quickly leads to brine formation, with a drop in performance. Finally, air quality. Dust and organic compounds foul the reactive bed and the heat exchangers.
Site watch-outs: corrosion, airtightness, fouling, safety
Chlorinated salts require a full material-compatibility review. Suitable stainless steel, polymers, coatings, and above all a clear separation between the humid zone and sensitive parts. Airtightness is both a design and an installation issue. Any stray air fault ruins charging. Add filtration, access hatches and instrumentation (temperature, humidity, pressure). On the safety side, address risks of local overheating, salt or brine leakage, and burns on hot surfaces.
Storage density: a clear comparison with a domestic hot water tank
Why density can be higher than hot water storage (and at what cost)
A tank stores sensible heat. Thermochemical storage (sorption or reversible reactions) can hold more energy per m³ because the energy is carried by a chemical state change, not only by a temperature delta. In return, you pay in complexity: airtightness, humidity management, heat exchanger, control. And often a tighter coupling to the generator.
Order-of-magnitude figures: energy stored per volume versus a 50 to 60 °C tank
| Solution | Assumption | Useful energy (kWh/m³) |
|---|---|---|
| DHW tank | Water from 10 → 55 °C | 45 to 55 |
| Thermochemical (material) | Lab value | 150 to 300 |
| Thermochemical (system) | Prototype | 80 to 200 |
Efficiency, power and losses: what you really gain and what you really lose
Clear advantage. When idle, losses are very low if the reactants are kept separate. Limits. Round-trip efficiency drops with auxiliaries (fans, pumps) and temperature differences. Delivered power depends on kinetics and exchange surfaces, and is often slower than in a tank. On site, define the charging conditions, the temperature range and the required power before validating a work package.
Seasonal storage: promises and constraints in single-family homes and multifamily buildings
Why it makes sense for shifting energy from summer to winter (solar thermal, heat pumps, heat recovery)
The idea is simple. Heat sources are often available in summer (solar thermal, cooling rejects, low-temperature waste heat), while heating demand is in winter. Seasonal storage aims to shift useful kWh, especially when you are working with low-temperature operating regimes and the heat pump can charge the store when its COP is favourable.
Two architectures: dry storage in a material vessel versus storage integrated into the network
In “dry” systems, energy is stored in a material (sorption, salts, zeolites). Thermochemical storage is attractive because it limits standby losses, but it requires humidity management, carefully designed heat exchangers and controlled regeneration. At network scale, the discussion is more about water volumes, borehole fields, ponds or aquifers. There, everything comes down to hydraulics, insulation, instrumentation and supply temperature.
Realistic use cases: DHW, heating top-up, and limits in retrofit work
In retrofit, start with realistic uses. DHW preheating, shoulder-season top-up, load shaving in multifamily buildings. The limits appear quickly: available space, floor loading, emitter compatibility, network balance and control. At this stage, we are still dealing with demonstrators. Include monitoring from the quote stage (sensors, metering, curves), otherwise the gain remains theoretical, and post-renovation energy consumption monitoring is often essential to verify the performance.
Maturity in 2026: where the technology stands and how to talk about it to your clients
Maturity level: demonstrators, pilots, partial feedback — not a mainstream product
In 2026, thermochemical storage is still mostly at demonstrator stage. There are pilot systems in real operating conditions, but with only partial feedback so far on cycle durability, moisture tightness, regeneration and hydraulic or air-side integration. For an off-the-shelf offering, the barriers are as much industrial as technical: safety, standardisation, training, spare parts.
What you can offer today: available alternatives (water, PCM, thermal mass) and common sense
To meet a day/night shifting need, offer proven solutions. Sensible heat storage in water (buffer tank, DHW tank, stratification), latent storage with PCM when the use case is clear, and building thermal mass when it is properly controlled. Common sense still applies: reduce losses, lower supply temperatures, control, measure.
Vocabulary and key messages to use: avoid overselling, frame lead times, after-sales and warranties
Talk about “pilot” and “feedback”, not “ready-made solution”. In your quotation, define the scope, commissioning time, supervision, and who is responsible for after-sales service. State the warranties available, and what remains outside standard coverage: consumables, sensors, maintenance, access to data.




