Blog/VMC anti-vibration mounts: choosing and buying the right model
Contractors

November 5, 2026

•

6 min read

VMC anti-vibration mounts: choosing the right part and buying it without making a mistake in 2026

To choose and buy a VMC anti-vibration mount without making a mistake, first size it based on the load per point, with a safety margin of 1.5 to 2 times the supported mass, then distribute the load over 4 supports as soon as the casing is long or asymmetrically loaded. As for stiffness, in practice allow 40 to 55 Shore A for light loads, and 60 to 70 Shore A if the allowable travel is limited, aiming for a service deflection midway through the stated travel. These values come from the body of the article, and they provide a numerical basis to compare quotes and troubleshoot before ordering, after ruling out impeller imbalance or duct contact.

Contents

Before buying: diagnose the source of the vibration (casing, duct or impeller)

Identify the symptoms: humming, attic resonance, vibration at the grille

Start by characterising the noise and how it spreads. A continuous hum often points to structural vibration in the casing. A strong resonance in the attic suggests contact with the framing, a hanger, rails, or a duct touching something. Vibration felt at the grille more often travels through the duct or comes from an imbalance on the impeller side.

Test methodically: suspended casing vs. floor-mounted casing, taut duct vs. free duct

  • Run the unit at several speeds. Note at which speed the vibration appears.
  • “Set-down” test. Temporarily place the casing on soft blocks. Compare it with the suspended configuration.
  • “Free duct” test. Relax a section, remove a contact point, then restart. Also check the clamps and the flexible sleeve.

Rule out false leads: wheel imbalance, dirt build-up, excessive airflow and fixings

A VMC anti-vibration mount will not correct an imbalance. Before ordering, check the wheel condition, fastener tightness, alignment, dirt build-up and casing fixings. Excessive airflow creates more of a rushing sound, but it can amplify an already present vibration. If the vibration drops after cleaning or re-centering, the part was not the cause. To complete the diagnosis, you can also carry out a ventilation airflow measurement with the appropriate tools.

Understanding the VMC anti-vibration mount families and what they are used for

Male-female rubber pad: the classic solution for suspending the casing

The male-female rubber pad remains the starting point for a casing VMC anti-vibration mount. Select it first by the allowable load per pad, then by stiffness. In practice, aim for a mainly compression-based mounting. Avoid permanent shear caused by an overlong rod or a misaligned casing. Also check the clearance under the casing and the tightening torque. Excessive crushing stiffens the assembly and lets vibration pass back through.

Spring anti-vibration mount: when the vibration frequency is pronounced

A spring becomes relevant when vibration is dominant and repetitive, typically on powerful casings or lightweight frame installations. Selection is based on the system’s natural frequency and static deflection. Add an elastomer interface to avoid any metal-to-metal contact and to absorb start-up shocks.

Bungee cord, textile strap and hangers: flexible solutions to reduce transmission to the structure

Bungee cords, straps and hangers are useful for decoupling ducts, branches and small casings, especially in attics. Check creep over time, ageing resistance and the fire behaviour of the support. Provide an accessible tension adjustment, otherwise the duct ends up bearing on the structure and transmission starts again.

Choosing the right VMC anti-vibration mount: allowable load, stiffness and operating mode

Size it by load: casing weight + accessories, safety margin and number of points

For a VMC anti-vibration mount, start with the actual weight of the casing. Add the accessories carried by the frame (silencer, coil, branch connections, sleeves), and anything that “pulls” on it (rigid duct sections, hangers). Apply a safety margin of 1.5 to 2 depending on the risk of imbalance and start-up conditions. Distribute the load over 4 points as soon as the casing is long or asymmetrically loaded.

Parameter Value Unit
Total mass M kg
Support points n pcs
Margin S (1.5 to 2) -
Load per point (M × S) / n kg

Understanding rubber hardness (Shore) and its effect on vibration isolation

Shore A hardness controls deflection under load. The softer it is, the lower the natural frequency and the better the isolation, but the casing may bounce and bottom out. Conversely, too hard transmits vibration. In practice, 40 to 55 Shore A for light loads, 60 to 70 Shore A if the allowable travel is limited. Aim for a service deflection halfway through the stated travel.

Compression or shear mounting: advantages, limits and common mistakes

In compression, the installation is simple and stable, but isolation may be mediocre if the rubber is too hard or the bolt is fully tightened. In shear, you often gain flexibility, provided the axis is respected and no tensile load is introduced. Common mistakes: metal-to-metal contact, washers that bridge the gap, or trying to compensate for a wheel imbalance or excessive airflow. Cleaning and balancing come before buying.

Anticipating ageing: why the mount hardens and when to replace it

Signs of wear: hardening, cracks, sagging and vibration coming back

A VMC anti-vibration mount does not just “squash down”. Over time, the elastomer stiffens and transmits structure-borne noise again. On site, look for the return of vibration at the casing, threaded rods or frame, then check the part. Typical signs: micro-cracks, insert separation, permanent marking, and sagging that puts the structure back under stress.

Real service life depending on conditions: temperature, humidity, mechanical stress and UV

Hardening mainly comes from thermo-oxidative ageing, ozone and UV, which alter the rubber’s cross-linking. Heat and humidity also speed up loss of elasticity and corrosion of the reinforcement. Compression-release cycles and shear loads increase fatigue. The result: hardness rises, damping drops.

Good maintenance practice: periodic checks, tightening, and decoupling the ducts

During maintenance, inspect the supports at every visit. Check tightening without over-compressing, and replace any corroded hardware. Decouple the ducts. Add a flexible sleeve if a duct pulls on the casing. If vibration persists, treat the cause first: dirt build-up, imbalance, bearing, excessive airflow. The anti-vibration mount will not compensate for an imbalance: in that case, refer to the guide on VMC maintenance.

Buying the part from the right source: compatibility, references and troubleshooting advice

Gather the right information before ordering: centres, threads, height, diameter and target load

Before buying a VMC anti-vibration mount, start from the casing nameplate and its support. Note the brand, the exact reference, the version (AC or EC motor), then measure on the part: centre distance, thread type, usable height, diameter and installation direction (compression or shear). Also set a realistic target load, taking into account dynamic forces and the location (ceiling, wall, frame).

Avoid unnecessary purchases: when you need to clean, rebalance or replace the impeller

A vibration does not always come from the mounting. If the noise changes with dirt build-up, start by cleaning the wheel and checking for play. In the case of imbalance, an anti-vibration mount sometimes masks the issue, then the vibration returns. If the wheel is bent, cracked or still unbalanced after cleaning, replace the impeller, or even the casing.

Point the customer toward the right ventilation solution: parts, accessories and alternatives depending on the job

Depending on the job, choose the original part, a compatible anti-vibration kit, or a change in layout (hangers, flexible sleeves, duct re-routing). If the network is too restrictive, correct pressure losses and airflow before increasing speed. The goal: a traceable, stable solution you can stand behind on the quote. To address the root cause on the network side, also see VMC duct airtightness.

Frequently asked questions

Calculate the load per mount: the casing weight and accessories divided by the number of support points, then aim for an actual compression of about 10–20% of the elastomer height. If the mount is overloaded, it crushes and stiffens the whole assembly; if it is underloaded, it does not work properly and allows vibration to pass through. Also check that the casing axis stays aligned to avoid permanent shear.

Share this article

Louis Meneteau

Louis is CPO of Argile. An engineer by training, he spent four years validating calculation software in systems engineering, then three years in software product. He turns the installer's daily reality into product workflows: technical survey, sizing, quotes and subsidy files. His articles describe field gestures rather than principles, because he watches them on site before specifying them.

Further reading

ContractorsNovember 17, 2026
DINplus or ENplus: choosing the right pellet certification

To qualify a “DINplus” bag on site, stick to the thresholds in the DINplus specification (DIN CERTCO): moisture ≤ 10%, ash ≤ 0.7%, fines in bag at delivery ≤ 1.0%, and mechanical durability ≥ 97.5%. These values frame what you can rely on in the event of fouling, auger jams or an after-sales dispute, but they mainly apply at the factory gate. If pellets go through bulk handling or storage outside the certified chain, ENplus A1 adds a traceability and logistics-control guarantee via the operator ID, which better secures the condition of the fuel on arrival.

6 min read

ContractorsOctober 24, 2026
Lambda coefficient: choosing the right value for your calculations

The lambda value to use is the one declared or certified for the product actually installed, not an average for its family. The French Th-Bât calculation rules convert it into a design value with a safety factor FR of 1 or 1.15 depending on where the declaration comes from and, where no value can be evidenced, impose default values that penalise the result: 0.055 W/(m·K) for glass wool of unknown density.

7 min read

ContractorsNovember 14, 2026
Damp basement ceiling: getting the diagnosis right before insulation

Before insulating a damp basement ceiling, carry out a diagnosis by measuring temperature, relative humidity and surface temperature, then calculate the dew point, because a wall at 12 to 16 °C can start condensing as soon as more humid summer air enters the basement. This approach is set out in the dew-point method in ADEME’s guide “Why and how to insulate your home,” which you can refer to if checked. If the source is still lateral water ingress or rising damp, sealing and wall treatment come first, and any underside insulation must be water-resistant or protected by a ventilated soffit.

6 min read

Reveal your expertise

One demo, and you see your expertise proven.

Contact us