Blog/Methane LHV values and conversions for your calculations
Contractors

November 13, 2026

•

6 min read

Methane LHV (methane LHV) in kWh per Nm³ and per kg: useful conversions in 2026

For your calculations, use a lower heating value (LHV) for pure methane (CH₄) of 9.94 kWh per Nm³ at 0 °C and 1.01325 bar, and 13.9 kWh per kg, values taken from reference thermochemical tables (NIST Chemistry WebBook) used in combustion calculations. These benchmarks apply only to pure methane: distributed natural gas is a mixture, and the bill is already converted into kWh using the delivery point conversion factor, which depends on the supply zone and the local higher heating value (HHV) applied by the distributor.

Contents

Make a clear distinction between LHV, HHV and units before calculating combustion

Methane LHV vs HHV: what you are actually measuring (and why the trap is common)

The LHV assumes that the water vapour formed during combustion remains in the gaseous state. The HHV also recovers the heat of condensation. In burner calculations, switching from one basis to the other shifts the balance by about 10%. Methane LHV is therefore a consistent basis if your efficiencies and gas flow rates are expressed on an LHV basis.

kWh, MJ, Nm³, meter m³ and kg: what each unit is for on site

kWh and MJ are energies. Nm³ is a volume referred to reference conditions (standardised temperature and pressure), which is essential for comparing gases. Meter m³ is the volume measured in service, then corrected. kg is used as soon as you move to a mass basis (LPG, heating oil, biomass) or for material balances.

When to use LHV in sizing (burner, boiler, gas heat pump) and when the bill is usually in HHV

For sizing (burner, boiler, gas heat pump), keep to one basis only. Use the LHV for useful thermal output and “on LHV” efficiencies. The gas bill, on the other hand, is most often in HHV kWh, after application of a conversion factor linked to the delivery point. Convert before comparing consumption with site calculations.

Reference LHV value for pure methane (CH₄)

Pure methane LHV in kWh/Nm³ (normal conditions must be specified): order of magnitude ≈ 9.94 kWh/Nm³

For your combustion calculations, use the methane LHV of pure methane at 9.94 kWh/Nm³, provided that you fix the normal conditions. In practice, 1 Nm³ corresponds to dry gas at 0 °C and 1.01325 bar (volumetric reference).

Reference temperature (°C) Reference pressure (bar abs) LHV (kWh/Nm³)
0 1.01325 9.94

Pure methane LHV in kWh/kg: order of magnitude ≈ 13.9 kWh/kg

On a mass basis, CH₄ LHV is close to 13.9 kWh/kg. This is the most robust value if your calculation starts from a mass flow rate or energy per tonne.

LHV (MJ/kg) LHV (kWh/kg)
50.0 13.9

How to convert from kWh/kg to kWh/Nm³ (CH₄ density at normal conditions) without making a mistake

The conversion uses the density at normal conditions, not a density at 15 °C or 20 °C. At 0 °C and 1.01325 bar, use ρ(CH₄) ≈ 0.717 kg/Nm³. Apply LHVvol = LHVmass × ρ.

Density ρ (kg/Nm³) Formula Example (kWh/Nm³)
0.717 13.9 × ρ 9.95

Why distributed natural gas is not pure methane: variations and conversion factor

Natural gas composition: how the mix (CH₄, C₂H₆, N₂…) affects calorific value

Methane LHV describes pure CH₄. But distributed natural gas is a mixture. It is mostly methane, but it also contains heavier hydrocarbons (ethane, propane), inert gases (nitrogen) and traces of CO₂. This mix changes the calorific value and therefore the energy actually available for the same gas quantity.

Supply zones, H gas/B gas and local variations: what changes from one delivery point to another

At the delivery-point level, quality depends on the supply zone. In France, a distinction has historically been made between H gas (richer gas) and B gas (leaner gas). Changes in source, interconnections and biomethane injection can create local differences. Direct consequence: sizing based on an “average” value can drift.

The distributor’s conversion factor: how billed kWh are calculated from m³ (and why this avoids “raw” m³)

Do not think in “raw” m³. The bill converts the measured volume into energy using a conversion factor. It incorporates the local gas characterisation (higher heating value retained for the delivery point) and a correction linked to measurement conditions (pressure, temperature, altitude). You then start from billed kWh, which is more robust for comparisons, combustion calculations or energy balance justification.

Practical conversions for your 2026 calculations: method and quick checks

Conversion formulas: meter m³ → billed kWh → LHV estimate (without mixing up LHV/HHV)

For your gas files, start from the meter reading, then stay aligned with the bill. Single reference only. The m³ → kWh conversion is done using the delivery-point conversion factor (it includes gas quality and corrections). To work back to an LHV energy value, then correct by the HHV/LHV ratio, not the other way around.

  • billed kWh = meter m³ × conversion factor (kWh/m³)
  • estimated LHV kWh ≈ billed kWh ÷ (HHV/LHV)
  • Nm³ required = LHV kWh ÷ methane LHV value (kWh/Nm³)

Temperature/pressure reference conditions: without them, a volumetric value has no meaning (Nm³ must be specified)

A value in kWh/Nm³ assumes a volume referred to normal conditions. State the reference clearly, typically 0 °C and 1.01325 bar. A cubic metre measured by the meter is not an Nm³. Without normalisation (T, P), volumetric LHV comparisons are not usable.

Field checks: spotting an inconsistency in 30 seconds (typical HHV/LHV ratios)

Quick check. If your kWh/m³ is well outside the usual local range, recheck the factor, period and index. To avoid an HHV vs LHV error, also check typical HHV/LHV ratios.

Fuel Typical HHV/LHV
Methane 1.11
Propane 1.09
Butane 1.09

Comparative table of LHVs for converting your fuels (tradesperson → site)

LHV table: methane (reference), propane, butane, heating oil, wood (with the most useful unit: kg, litre, stere)

Calculation basis. LHV at standard conditions for volumetric values. For methane LHV, work in Nm³ (dry gas, 0 °C, 1.01325 bar) or in kg depending on your model.

Fuel Unit LHV (kWh/unit) Site reference
Methane (pure) Nm³ 9.95 Lab value, not network gas
Methane (pure) kg 13.9 Useful for combustion/mass flow
Propane kg 12.9 Pressurised LPG
Butane kg 12.7 Pressurised LPG
Heating oil L 10.0 Varies with density
Firewood (≈20% H2O) stere 1,600 Highly dependent on moisture/species

Conversion examples: turning a 10,000 kWh requirement into a fuel quantity (propane/heating oil/wood)

Fuel Quantity for 10,000 kWh
Propane ≈ 775 kg
Heating oil ≈ 1,000 L
Firewood (≈20% H2O) ≈ 6.3 stere

Key points by fuel: wood moisture, heating oil density, storage and safety for LPG

  • Wood. Measure moisture on site. At 30% H2O, useful LHV drops sharply and sizing drifts.
  • Heating oil. If you convert to kg, apply the actual density (often 0.83 to 0.86 kg/L depending on batch and temperature).
  • LPG (propane/butane). Check storage volume, regulatory clearances, ventilation and hazard zones. One oversight leads to non-compliance.

Key figures

10 %

LHV vs HHV gap

9.94 kWh/Nm³

Volumetric CH4 LHV

0.717 kg/Nm³

CH4 density (0 °C)

Frequently asked questions

For methane, the HHV is generally about 10% higher than the LHV because it includes the heat of condensation of water vapour. To avoid a distorted efficiency figure, check whether your data are stated “on LHV” (sizing, manufacturer efficiencies) or “on HHV” (billing), then convert everything to a single basis before comparing.

Share this article

Louis Meneteau

Louis is CPO of Argile. An engineer by training, he spent four years validating calculation software in systems engineering, then three years in software product. He turns the installer's daily reality into product workflows: technical survey, sizing, quotes and subsidy files. His articles describe field gestures rather than principles, because he watches them on site before specifying them.

Further reading

ContractorsOctober 24, 2026
Lambda coefficient: choosing the right value for your calculations

The lambda value to use is the one declared or certified for the product actually installed, not an average for its family. The French Th-Bât calculation rules convert it into a design value with a safety factor FR of 1 or 1.15 depending on where the declaration comes from and, where no value can be evidenced, impose default values that penalise the result: 0.055 W/(m·K) for glass wool of unknown density.

7 min read

ContractorsNovember 15, 2026
Roof slope: calculating the developed area for your quote

For a quote, use the developed area of the roof slope, calculated with the coefficient k = 1 / cos(θ) (or k = √(1 + (p/100)²) if the pitch is expressed in %), then developed area = projected area × k. This formula comes from trigonometry (cosine in a right triangle) and, in the body example, a 35° pitch gives k ≈ 1.22, i.e. 133 m² developed instead of 109 m² projected. This is the value that secures your quantities of insulation, hangers and vapour barrier, and it also serves as the basis for roof heat losses.

6 min read

ContractorsMay 31, 2026
How to choose the extraction for your heat-pump water heater?

On a heat-pump water heater, the extracted air often makes the difference between a silent installation and a unit that draws too hard on the room. In renovation, you mainly need to secure three points: where to capture the air, where to discharge it, and how to avoid odours, humidity or cold draughts coming back. With a simple method, you save time on site and deliver stable comfort to the client.

5 min read

Reveal your expertise

One demo, and you see your expertise proven.

Contact us